INTERLOGIC INDUSTRIES A104-FM Modem Type Data/Fax Maximum Data Rate 2400 bps Maximum Fax Rate 9600 bps Data Bus Unidentified Fax Class Unidentified Data Modulation Protocol Bell 103A & 212A, CCITT V.22 Fax Modulation Protocol Unidentified Error Correction/Compression CCITT V.42 & V.42bis, MNP 5 [Image] CONNECTIONS Purpose Location Purpose Location Line in CN1 Line out CN2 COM PORT SETTINGS COM JP1 JP2 JP3 COM4 Pins 2 & 3 Pins 2 & 3 Pins 2 & 3 closed closed closed COM1 Pins 1 & 2 Pins 1 & 2 Pins 1 & 2 closed closed closed COM2 Pins 2 & 3 Pins 2 & 3 Pins 1 & 2 closed closed closed COM3 Pins 1 & 2 Pins 1 & 2 Pins 2 & 3 closed closed closed CONNECTOR JP4 Purpose Location Pair 2 Tip & Ring Pins 1 & 4 Pair 1 Tip & Ring Pins 2 & 3 S14 -BIT MAPPED CONFIGURATION REGISTER Value Range: Bit-mapped Default: 1 Type: Read/Write In Stored Profile?: Yes Description: Bit Mapped Configuration Register Bit Value Function 0 0 Not used 1 1 Enable: Command echo (E1) 0 Disable: Command echo (E0) 2 0 Enable: Result codes (Q0) 1 Disable: Result codes (Q1) 3 1 Set result codes to word (V1) 0 Set result codes to digit (V0) 4 0 Not used 5 1 Set to Pulse dial (P) 0 Set to Tone Dial (T) 6 0 Not used 7 1 Enable: Originate mode 0 Enable: Answer mode S21 -BIT MAPPED CONFIGURATION REGISTER Value Range: Bit-mapped Default: 1 Type: Read/Write In Stored Profile?: Yes Description: Bit Mapped Configuration Register Bit Value Function 0 0 Not used 1 0 Not used 2 0 Not used 3 & 4 00 Sets modem to ignore DTR (&D0) 01 ON-to-OFF transition on DTR forces the modem to enter the command mode (&D1) 10 ON-to-OFF transition on DTR forces the 11 modem to hang up (&D2) ON-to-OFF transition on DTR forces the modem to reset (&D3) 5 0 Enable: DCD always ON (&C0) 1 DCD checks the actual state of the data carrier (&C1) 6 0 Not used 7 0 Disable: Long Space Disconnect (Y0) 1 Enable: Long Space Disconnect (Y1) S22 -BIT MAPPED CONFIGURATION REGISTER Value Range: Bit-mapped Default: 1 Type: Read/Write In Stored Profile?: Yes Description: Bit Mapped Configuration Register Bit Value Function 0 & 1 10 Speaker volume set to medium (l1) 00 Speaker volume set to low (l0) 01 Speaker volume set to low (l1) 11 Speaker volume set to high (l3) 2 & 3 01 Enable: Speaker on until carrier detected (M1) 00 Disable: Speaker (M0) 10 Enable: Speaker always on (M2) 11 Enable: Speaker on until carrier detected but Off during dialing (M3) 4 & 5 & 6 111 Enable: fourth extended result code set (X4) 000 Enable: basic result code set (x0) 100 Enable: first extended result code set 101 (X1) 110 Enable: second extended result code set (X2) Enable: third extended result code set (X3) 7 0 Set Make/Break ratio is 39/61 for USA (&P0) 1 Set Make/Break ratio is 33/67 for UK/HK (&P1) S23 - BIT MAPPED CONFIGURATION REGISTER Value Range: Bit-mapped Default: 1 Type: Read/Write In Stored Profile?: Yes Description: Bit Mapped Configuration Register Bit Value Function 0 1 Disable: Accept request from remote modem for a remote digital loopback (&T5) 0 Enable: Accept request from remote modem for a remote digital loopback (&T4) 1 & 2 & 3 000 300 bps 001 600 bps 010 1200 bps 011 2400 bps 100 4800 bps 101 9600 bps 4 & 5 00 Enable: Even parity. 01 Enable: Space parity. 10 Enable: Odd parity. 11 Enable: Mark parity. 6 00 Disable: Guard tone (&G0) 01 Enable: 550 Hz guard tone (&G2) 10 Enable: 1800 Hz guard tone (&G2) 11 Not used S27 -BIT MAPPED CONFIGURATION REGISTER Value Range: Bit-mapped Default: 1 Type: Read/Write In Stored Profile?: Yes Description: Bit Mapped Configuration Register Bit Value Function 0 0 Not used 1 0 Not used 2 0 Not used 3 0 Not used 4 0 Not used 5 0 Not used 6 1 Enable: Bell 212A with 1200bps, Bell 103 with 300bps (B1) 0 Enable: CCITT V.22 with 1200bps; V.21 with 300bps (B0) 7 0 Not used